Architectural shingles
Metal roofing
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Tamko Flashing Replacement: The Paradise Owner’s Guide
We install Tamko-compatible flashing replacement in Paradise, and most jobs land between $280 and $650 installed, depending on how much counter-flashing and sealant work the detail needs. On a straightforward exposed nail or pipe boot we can often be on your roof the same day you call, weather permitting. We’re an independent roofing company, not affiliated with Tamko, but we set the brand regularly.
Owners usually find out the flashing failed the hard way. There’s a brown ring on the ceiling below the chimney, or a rust streak down the siding after a windy night. Some spot the old flashing first, lifted at a corner or with the mastic cracked away. In Paradise, the afternoon sun and the swing between hot days and cool nights work on sheet metal and sealant until something lets go. That’s when the drip starts, and it’s why we tell people to catch it before the next rain.
Which Tamko Models This Applies To
Tamko flashing turns up around chimneys, step walls, valley edges, pipe boots and drip edges on plenty of Paradise roofs, and you don’t need the exact shingle line to replace a failed piece. Flashing is a roofing component, so the real question isn’t which Tamko shingle sits above it, it’s the size, profile and metal of the piece you’re swapping. We match the replacement to the opening: chimney widths, the step of your wall cladding, the pipe diameter, the roof pitch. If your old piece is stamped or labeled with a Tamko part number, bring it. If the label wore off years ago, we measure instead.
Here’s where a lot of owners get tripped up: an aftermarket boot or step piece that “fits” on the shelf often isn’t the same gauge or the same sealing profile as the original, and it fails faster in our heat. A good aftermarket equivalent can do the job when the gauge and the flange width are right. A cheap one can’t. We’d rather show you the two side by side and explain the difference than talk you into either. If you’ve got Tamko, or GAF, Owens Corning or CertainTeed up there, the matching works the same way.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Signs Your Tamko Flashing Replacement Is Failing
- Rust streaks or white mineral staining down the wall or siding. That’s the metal or the sealant breaking down and shedding, and it usually shows up before any water gets inside. When you see it low on a wall below a chimney or a step, the flashing above is the first place we look.
- A brown ring or stain on the ceiling or the wall below a roof detail. Water has already worked past the flashing and is tracking down framing before it shows on drywall. By the time the stain appears, the leak has been running for a while.
- Cracked, peeling or missing mastic along the flashing edge. Sealant takes a beating in Paradise heat and shrinks away from the metal over time. Once it opens up, wind-driven rain gets under the flange.
- Lifted, curled or loose flashing at a corner or against a wall. Fasteners back out and the metal lifts, and a lifted edge is a scoop for rain. This one you can sometimes spot from the ground with binoculars.
- Damp or soft sheathing around a pipe boot or valley edge. This is the late-stage sign, and it means the deck underneath is taking water. We always pull back the shingle course to check the deck before we quote the fix.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Paradise, flashing replacement runs about $280 to $650 installed for a typical detail, and the range tracks a few real things: the length and type of metal, how many pieces it takes, whether counter-flashing and a new seal are needed, and how much shingle has to come up to reach sound deck. We give you the price as a line item, parts and labor shown separately, so you can see what you’re paying for. If the deck is soft under the flashing, that’s a separate repair and we show you the photos before we touch it.
Every flashing job we do is covered by the written 90-Day Done Right Promise, and a free second opinion on any written estimate is always on the table. There’s no trip charge inside our own county. We don’t claim to carry parts on a truck or stock them in a shop, so lead time depends on sourcing the right piece. We order it, show you what came in, and set it. A roof detail is only as good as the deck underneath, so we check that first.
DIY or Call Us?
Some of the checking is safe to do yourself. Look at the flashing from the ground, note where the stain or the rust is, and take a photo so we can talk it through. Check the label on the piece if it’s still legible. What we don’t recommend is the swap itself, especially on a steep pitch or a tall chimney, where a slip is a serious fall and the flashing has to tuck under shingle courses and seal correctly or it will leak again in the first hard rain.
The part that goes wrong is almost always the sealing and the tuck, not the metal. Get that wrong and it’s a repeat leak in the same spot. Call (833) 676-0557 and we’ll look with you, answer the phone with a live person, and get it right. Same address since 1996, and the guys on the roof are Bill’s own crew.
FAQs
Good metal flashing can last 15 to 20 years, but the sealant and the exposed edges are what give out first in Paradise’s sun and heat swings. A year of that is harder on a seal than a decade in a milder climate, so we check sealant every few years.
Sometimes, when the metal is still sound and only the sealant failed, a repair is the right call and we’ll tell you so. Once the metal is rusted through or the flange is lifted, replacement is cheaper than chasing a leak. We’d rather fix the small thing than sell you the big one.
Most flashing details take a few hours once the correct piece is on hand, and we always pull back the course to check the deck first. Your timing depends on what’s underneath and on sourcing the right part.
We measure the opening, match gauge and profile, and order the correct piece, whether it’s Tamko-compatible or an equivalent from another maker we set. You see it before it goes on.
The best way to know your number is to have us look. Call (833) 676-0557 for a free estimate in Paradise. We’re locally owned, owner-operated, and we’ll show you the photos before we talk money.
Written by the team at Shepherd & Sons Roofing Paradise, serving Paradise and nearby areas.