Metal roofing
Architectural shingles
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Owens Corning Metal Roofing in Paradise: What to Know First
We install and repair Owens Corning metal roofing in Paradise as an independent Owens Corning service provider, and most metal roof projects here run three to six days from tear-off to final walkthrough. On cost, expect to talk real numbers: a full standing seam replacement in Paradise generally lands between $18,000 and $34,000 depending on square count and panel style, and we put that range in writing before anyone touches your roof. This page is for Paradise homeowners who already own an Owens Corning roof or metal system and want straight answers on what’s failing, what it costs to fix, and who’s accountable. Call (833) 676-0557 and a live person picks up, day or night.
How Owens Corning Products Fail – and How We Fix Them
Owens Corning makes good metal systems, but metal in Paradise’s climate fails in ways homeowners don’t expect. Here’s what we actually see on Paradise roofs, and what we do about it.
- Standing seam panel fastener back-out on the valley-side runs. Owens Corning standing seam panels are typically secured with concealed clips, but we still find screws backing out along the eave and ridge where Paradise’s summer thermal swing works them loose. The real cause is usually an under-driven clip at install, not wind. We replace the clips, re-torque to spec, and add a proper closure at the eave before we call it done.
- Metal shingle lift at the course edges. Owens Corning metal shingle profiles can lift at the bottom course when the starter strip wasn’t fastened tight to the deck. On Paradise roofs facing full afternoon sun, that lift shows up as a rattle in high wind before you ever see daylight. We reset the course, re-fasten the starter, and check the whole field for the same pattern.
- Corrugated panel rust at the cut edges. Owens Corning corrugated steel panels cut on-site without a re-coat will flash rust at the exposed edge first – it’s the fastest place to spot trouble. We re-coat every field cut and use pre-cut panels where the span allows.
- Coating chalk and fade on aluminum panels. Owens Corning aluminum systems hold up well to heat, but in Paradise the factory finish will chalk and fade at the sun-facing planes over time. That’s cosmetic, not structural – we tell homeowners the truth instead of selling a replacement. When it’s time to recoat, we prep and coat rather than tear off a sound panel.
- Condensation and fastener leaks at penetrations. Metal over an unconditioned attic in Paradise’s dry heat can sweat at the underside, and that moisture finds the lowest fastener. We check the underlayment and penetration gaskets first, because the leak is rarely where the stain shows.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Our Owens Corning Metal Roofing Process
- 1
Free estimate and a real look. I’ll show you the deck photos before we talk money. If the metal itself is fine and the flashing is the problem, you’ll hear that.
- 2
Measure the squares. A roof is measured in squares – ask any bidder how many they counted. We give you that number in writing.
- 3
Diagnose the system, not just the leak. We trace the water back to the actual failure point, whether that’s a clip, a cut edge, or a penetration gasket. Owens Corning work often needs the OEM profile matched, so we confirm the panel series before ordering.
- 4
Parts decision. We match Owens Corning OEM panels and closures where the warranty depends on it, and use quality aftermarket fasteners and sealant where OEM adds cost without adding life. Either way, you know which is which and why.
- 5
The repair or install. Standing seam, metal shingle, corrugated, aluminum or steel – the nailing pattern and clip spacing earn the wind rating, not the shingle wrapper.
- 6
Test and walkthrough. We flood-test the repaired runs and walk the roof with you before we leave. Every roofing job is covered by our written 90-Day Done Right Promise – one call brings Bill back.
See the difference
Before
After
Before
After
Before
AfterWhat Owens Corning Metal Roofing Costs in Paradise
Real ranges for the Owens Corning metal work we do in Paradise. These are honest ballparks – your exact quote comes free after we measure.
- Metal roof repair (leak, clip, flashing): $350 to $1,200 depending on access and panel count.
- Corrugated steel panel install: $11,000 to $19,000 for a typical Paradise single-story roof.
- Metal shingle install: $15,000 to $26,000.
- Standing seam install: $18,000 to $34,000.
- Metal roof coating / recoat: $2,500 to $6,500.
What moves the price: square count, roof pitch, how many penetrations and valleys, whether we’re working over the old roof or tearing off, and which panel series you choose. Free estimates, a free second opinion on any written estimate you already have, no trip charge inside our own county, and a flat $40 off any repair over $200. Call (833) 676-0557 to schedule your free estimate.
Why Paradise Homeowners Call Shepherd & Sons Roofing Paradise for Owens Corning Work
Same address since 1996. That’s 29 years in the same shop with the name on the truck matching the name on the license, while out-of-state storm chasers come and go after every hailstorm. Bill’s own sons are on the roof with him, and our technicians have up to 30 years of experience with Owens Corning and the rest of the trade. We also install and repair GAF and CertainTeed products, so we’ll tell you honestly when an Owens Corning system is the right call for your Paradise roof and when it isn’t. Every job carries the written 90-Day Done Right Promise. Ask anyone on your street – the name on the truck is the name on the license.
FAQs
Not if it’s done with matching Owens Corning materials and proper fastening – a warranty-voiding repair is one that mixes the wrong panel series or skips the OEM closure. We work warranty-safe and tell you which parts have to be OEM before we order them. Call (833) 676-0557 for a free estimate.
Yes. Owens Corning standing seam, metal shingle, and corrugated profiles are all available to us, and we confirm your exact series so the replacement panels match. If a part is on backorder, we tell you the real lead time instead of guessing. Estimates are free.
Repair if the panel field is sound and the problem is clips, flashing, or a penetration leak – we see that on most Paradise metal roofs that are only a few years old. Replace only when the panels themselves are rusted through at the cut edges or the underlayment has failed across the whole field. We’ll show you the deck photos either way.
A live person answers our phone 24/7 and we’ll have someone out to look at your Paradise roof for a free estimate, usually within a few days. Storm damage gets triaged first. Call (833) 676-0557 to get on the schedule.
Paradise and the surrounding county, plus nearby towns. No trip charge inside our own county, so the estimate number is the number. Call (833) 676-0557 for your free estimate.
Written by the team at Shepherd & Sons Roofing Paradise, serving Paradise and nearby areas.