Architectural shingles
Metal roofing
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
CertainTeed Flashing Replacement: The Paradise Owner’s Guide
If you have a failed section of CertainTeed roof flashing in Paradise, we replace it with a compatible new piece, and a typical installed repair runs roughly $285 to $650 depending on how much roof has to be opened up and whether the leak has already reached the sheathing. Most flashing replacements we do here in Paradise are small enough to schedule within a day or two of your call, not weeks out.
Owners in Paradise usually find this the same way: a brown ring on a ceiling corner after a monsoon, dark staining on the fascia under a sidewall, or a drip line down a stucco wall that only shows up when the wind pushes rain sideways. By the time you see the stain, the flashing has been quietly failing for months. The drip is the last symptom, not the first.
Which CertainTeed Models This Applies To
Flashing is not model-specific the way a shingle is. CertainTeed shingle lines – Landmark, XT 25, Independence, Northgate, Presidential – all get flashed the same way at the same penetrations: sidewalls, plumbing stacks, valleys, chimney walls, and the headwall where the roof meets a stucco face. What actually matters is getting the profile right for what the roof is shedding against. A low-slope section under a carport needs a different coil stock than a steep sidewall on a Landmark roof.
To identify yours, climb no higher than you can safely reach from a ladder or a second-story window and look for the CertainTeed name printed on the shingle tabs themselves – every legitimate CertainTeed shingle carries the brand on the face. Then measure the vertical leg of the existing flashing. If it is 3 inches, you need 3 inches, not 4, because a taller leg forces the counterflashing to sit proud of the stucco and you get a new gap to chase.
The OEM-versus-aftermarket decision is simpler than it sounds. CertainTeed-branded flashing accessories exist, but on nearly every Paradise roof the piece being replaced is generic coil stock that happened to be installed over CertainTeed shingles. If the existing corner is a fabricated piece, we fabricate the replacement to match. If it is a stamped product, we match the gauge and profile and paint the exposed edge to match. We are an independent service provider and not affiliated with CertainTeed, so we have no reason to upsell you a branded piece you do not need.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Signs Your CertainTeed Flashing Replacement Is Failing
Flashing almost never fails all at once. It goes in stages, and if you catch it in stage two you save yourself a deck repair.
- Caulk lines that have dried and pulled: The sealant at the top of the flashing shrinks as it ages – on sun-baked Paradise roofs, a sealant joint that was tight at install can be a separated crack within a few summers. The cracking is not the failure, it is the warning shot.
- Rust bleeding down a stucco or fascia face: Galvanized steel flashing in the Nevada desert takes ultraviolet year-round and cools fast at night. That swing drives moisture in and out of the metal until rust blooms appear where the leg meets the wall.
- Paint or elastomeric peeling at the wall transition: Water is getting behind the coating from above. Peeling paint on the wall directly above a roof line is one of the most reliable early signals of a failed wall flashing.
- Soft or discolored sheathing you can reach from the attic: Reach up past the fascia with a hand and feel the underside of the roof deck at the wall line. Dark wood or a soft patch means water has already passed the flashing and is working into the deck.
- Drip tracks and mineral stains on the ceiling corner: The stain is confirmation, not early warning. The flashing failed, the water ran down the truss, and now it is showing up inside your house. This is the stage where a $400 flashing repair can become a $1,800 drywall and framing repair if it waits.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Flashing replacement in Paradise runs about $285 to $650 installed, and that range covers the new flashing, the fasteners, the sealant, and the labor to lift and reset the shingles. Same range applies whether it is a plumbing stack collar, a sidewall section, or a small valley edge.
What drives the number is how many roof courses we have to open to get a clean install. A stack collar accessed from open roof is at the low end. A sidewall under a low eave that requires lifting three courses of Landmark runs toward the top. Chimney counterflashing and complex valley work can push past $650, and we will tell you that on the estimate, not after.
The 90-Day Done Right Promise is in writing on this job just like every other one we do. If the new flashing leaks in the first 90 days, one call brings us back, no argument. We do not charge a trip fee inside the county.
DIY or Call Us?
An owner can safely do the inspection work. From the ground with binoculars, from a ladder you have actually leaned against the house, or from inside the attic, you can confirm rust, peeling, and darkening. That is enough to know you have a problem.
The installation is where DIY goes wrong. To replace flashing properly, you have to lift the shingle course above the flashing without cracking it, set the new piece, re-nail it in the correct pattern, and re-seal the top edge – and if the shingle above is already brittle from Nevada sun, lifting it breaks it and your flashing repair becomes a shingle repair. On a low-slope section, improper underlap means the new flashing sheds water the wrong direction and the next storm finds the back side of the wall. That is the failure pattern I see most on Paradise homes where the owner tried a weekend fix. Call us at (833) 676-0557 and we will take a look before you cut into anything.
FAQs
Most flashing on a Paradise roof lasts 15 to 25 years depending on material – galvanized steel is on the short end, copper and lead on the long end. Here is the specific gotcha: the UV and temperature swings in Paradise shorten the sealant life well before the metal gives out, so you will often need to re-seal or replace a 10-year-old piece of perfectly good metal because the joint failed. Call us at (833) 676-0557 for a free estimate and we will tell you which it is.
Sometimes – a re-seal on an otherwise sound piece is a real option and costs far less. It works when the metal is intact and only the caulk joint has failed. It does not work when the metal is rusted through, pitted, or has come loose from the wall, and in that case replacement is the honest answer. We will tell you which one you have after we look.
A single stack collar or short sidewall section takes two to three hours, and most Paradise jobs are done in one visit. Chimney counterflashing and multi-section work can run a full day. We schedule these based on the weather window, so you are not leaving an open roof through a monsoon afternoon.
We match the profile, gauge, and finish to what is already on the roof – not just the brand name. CertainTeed shingles are the shingle; the flashing itself is usually industry-standard coil stock or a stamped piece we fabricate or source to match. We also work with GAF and Owens Corning roofs on the same principle. If you want a free second opinion on another bidder’s number, we will look at it at no charge.
If you have a failed flashing section on a Paradise roof and you want to know what it will actually cost before anyone touches shingles, call Shepherd & Sons Roofing Paradise at (833) 676-0557. We answer live, day or night, and we will have Bill or one of the crew out to look at it – no trip charge inside the county, and the number we give you is the number on the estimate.
Written by the team at Shepherd & Sons Roofing Paradise, serving Paradise and nearby areas.