Architectural shingles
Metal roofing
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Boral Gutters & Accessories in Paradise: What to Know First
We install, repair, and replace Boral gutters and accessories in Paradise as an independent Boral service provider, and most straightforward jobs – a resealed run, a replaced downspout, fresh hangers – are finished in a single visit. Full seamless runs on a typical Paradise ranch home usually take one to two days once we’ve measured. You’ll get a written line-item quote before anyone touches your roofline, free estimates are standard, and we don’t add trip charges inside our own county.
This page is for Paradise homeowners who already have Boral product up on the fascia – whether it came with the house or you picked it out yourself – and want someone who has actually handled the stuff. Boral makes good material. It also has a few habits that show up in the desert that other brands don’t share. Call (833) 676-0557 and a live person picks up, day or night.
How Boral Products Fail – and How We Fix Them
Boral’s gutter line is aluminum and steel, typically run in seamless lengths and fitted with Boral hangers, end caps, and downspout fittings. What we see in Paradise isn’t the metal giving out – it’s the joints, the fasteners, and the way the material handles our particular weather. Here’s what actually shows up on our call-backs.
- Seam and corner failures on Boral aluminum runs. Boral’s factory seams and corner welds are solid, but the sealant used at field joints dries out faster here than in wetter climates. Paradise sits at the edge of the Mojave, and summer highs over 110°F bake the sealant at the corner miters until it cracks and lets go. We clean the joint back to bare metal and reseal with a high-temp-rated gutter sealant rather than a general-purpose caulk.
- Hanger pull-out on Boral fascia-mounted brackets. Boral’s hidden hangers rely on a solid fascia board behind them. In Paradise, fascia that’s been sun-baked for fifteen or twenty years gets brittle and splits around the screw, so the hanger backs out and the run sags. We check fascia condition before we re-hang anything, sister in new wood where it’s punky, then fasten into sound material.
- Downspout separation at Boral slip joints. The slip-joint fittings on Boral downspouts are press-fit, and they loosen over a few seasons of thermal expansion on a south-facing wall. That’s the source of a lot of “mystery” staining on stucco near the foundation. We re-crimp and re-secure the joints and check the elbow-to-drain connection so water actually leaves the wall.
- Gutter-guard mismatch on Boral runs. Homeowners sometimes add a universal guard to a Boral gutter and find it doesn’t seat right, because the profile and the hanger spacing don’t line up. We fit guards that match the Boral profile and set them at the correct pitch so water still moves to the outlet.
- Overflow at the factory end caps. A Boral run pitched slightly flat will pool at the end cap, and the cap is the first thing to leak. Rather than just resealing, we re-pitch the run so it drains toward the downspout. That’s a measurement job, not a caulk job.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Our Boral Gutters & Accessories Process
- 1
The call. A live person answers – not a form, not voicemail. Tell us what you’re seeing: water at the foundation, a sagging run, a downspout that’s pulled loose. We’ll set a time.
- 2
The look. Bill or one of the crew comes out, gets on the roof, and takes photos of the deck and the gutter line. You see the photos before we talk money. We measure the run in linear feet and note the Boral profile and hanger type so we quote the right parts.
- 3
The parts decision. We’ll tell you straight whether OEM Boral fittings are the right call or whether a quality aftermarket piece is the smarter buy for that spot. Sometimes OEM is worth it for a clean match; sometimes it’s money for nothing. We explain the trade-off and let you decide.
- 4
The work. We re-pitch, re-hang, reseal, or replace as needed, working to the Boral profile so the finished run looks like it was always there.
- 5
The test. We run water and watch it. Every joint, every downspout, every end cap. If it doesn’t flow right, we’re not done.
- 6
The promise. Every job is backed by our written 90-Day Done Right Promise. If something’s off, one call brings Bill back to make it right.
See the difference
Before
After
Before
After
Before
AfterWhat Boral Gutters & Accessories Costs in Paradise
Here’s what Boral gutter work runs in Paradise, based on the jobs we’ve done here. Every quote is line-item and written, and free estimates are standard.
- Reseal and re-crimp a field joint or downspout slip joint: $95 – $180 per spot.
- Replace a failed Boral hanger, with fascia repair if needed: $60 – $150 per hanger, depending on wood work.
- Downspout replacement (one run): $150 – $320.
- Gutter-guard install on an existing Boral run: $8 – $14 per linear foot.
- Seamless Boral gutter replacement, per linear foot: $9 – $18, with the upper end on two-story runs and heavy fascia work.
- Fascia repair behind the gutter: quoted by the job once we’ve seen the wood.
Two-story access, rotted fascia, and long runs with multiple corners all move the number. You’ll know it before we start. Call (833) 676-0557 for an exact quote – estimates are free.
Why Paradise Homeowners Call Shepherd & Sons Roofing Paradise for Boral Work
We’ve been at the same address since 1996, and the same name is on the license and the truck. When a storm rolls through Paradise and the phone lines light up, a live person still answers – not a call center three states away. The crew is background-checked, and Bill’s own sons work the roof with him.
We know Boral, and we also install and service GAF, Owens Corning, and CertainTeed, so we’re not going to force a brand on you when a different one fits better. Our technicians have up to 30 years of experience, and every job carries the 90-Day Done Right Promise in writing. Storm chasers leave after the season. We’re still here, same address, same name.
FAQs
No. Repairs done correctly with compatible materials don’t void a Boral warranty – what can void it is using incompatible parts or improper installation. We work with the Boral profile and document what we do, so you keep your coverage intact.
Both, depending on the spot. We’ll tell you when OEM Boral fittings are the right match and when a quality aftermarket piece does the same job for less, and we explain why before you decide.
Repair is usually the right call when the Boral run is mostly sound and the failure is at joints, hangers, or downspouts. Replacement makes more sense when the run has lost its pitch across the length, fascia is failing along most of it, or it’s sagged in several places. We’ll give you a straight answer either way.
We can usually get out within a few days for routine repairs, and faster when water is actively causing damage. Call (833) 676-0557 and a live person will pick up and get you on the schedule.
No. You get a written line-item quote before we start, and if we find something you didn’t know about – like rotted fascia – we stop and get your approval first. No surprise numbers at the door.
Written by the team at Shepherd & Sons Roofing Paradise, serving Paradise and nearby areas.
Call (833) 676-0557 for a free estimate on your Boral gutters and accessories in Paradise. A live person answers, day or night. Standing offers include $40 Off Any Repair Over $200, a free second opinion on any written estimate, no trip charge inside our own county, and a 10% senior and veteran discount.