A Shepherd company - serving Paradise, NV

Boral Flashing Replacement in Paradise, NV

Architectural shinglesArchitectural shingles
Metal roofingMetal roofing
Tile roofingTile roofing
GAFGAF
Owens CorningOwens Corning
Flat & low-slopeFlat & low-slope
Every visit starts with

Free roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation

We have financing partners for your new roof*On approved credit; ask us about your options
Get your free estimate

Boral Flashing Replacement: The Paradise Owner’s Guide

Boral-compatible flashing replacement in Paradise typically runs $310 to $780 installed, depending on the run length, the roof pitch, and whether the flashing ties into a wall, a valley, or a vent stack. We schedule Boral flashing work for Paradise homeowners Monday through Saturday, and on planned replacements we’ll give you a window and stick to it.

Call (833) 676-0557

Owners almost never go looking for flashing. They find it after a rain. You notice a rust-colored stain on the fascia below a wall line, or a curl of sealant peeling up at the roof-to-wall joint. Sometimes it’s a plumber or HVAC tech who points it out while they’re up there for something else. The flashing isn’t always the failure – but on a Boral roof that’s past its twentieth year, it’s the first thing we check, and often the first thing that’s actually letting water in. Written line-item quotes, fixed pricing, no change orders once the work starts.

Which Boral Models This Applies To

Boral’s roof line covers tile, shingle, and concrete products, and each one has its own flashing detail. On Boral tiles, the flashing profiles you’ll see are the standard step flashing at sidewalls, counter-flashing at headwalls, and the tile-specific pieces Boral sells alongside its field tile. On Boral’s shingle lines, the flashing is closer to standard – step, apron, valley metal – and manufacturer-approved details matter more than brand. There’s no universal Boral flashing part number, and anyone who tells you there is hasn’t read the installation manual.

The gotcha: Boral flashing dimensions are set by profile, not by the shape of your roof. Two Boral roofs on the same block can take different flashing widths. If the flashing you’re replacing was installed with the original roof and the roofers cut a tile profile flashing to fit around a wall, the replacement has to match the cut, not just the nominal size. Measure the actual exposed metal – the visible leg, not the flange under the tile – and bring that number to whoever’s quoting. We measure on site before the truck leaves, every time.

The OEM-versus-aftermarket call: on Boral tile work, use Boral’s or a manufacturer-approved equivalent. Aftermarket flashing stamped from 26-gauge galvanized doesn’t match the mill-finish or the dimensions Boral specs, and on a curved or mission-profile tile line the wrong flashing is a slow leak. On Boral shingle roofs, a quality 24-gauge painted steel or copper flashing is a fine substitute, and often a better one than what was there. We install products from GAF, Owens Corning, and CertainTeed on roofing work too, and Boral is one of the brands we’ve been setting for years – we’ll tell you straight which flashing makes sense for your roof. We’re an independent service provider, not affiliated with Boral.

Ask anybody bidding the job how they identified the Boral line on your roof. If they can’t point to the tile or shingle edge and name the profile, they’re guessing on the flashing.

Explore

Styles & brands we work with

  • Architectural shingles
  • Metal roofing
  • Tile roofing
  • GAF
  • Owens Corning
  • Flat & low-slope

Signs Your Boral Flashing Replacement Is Failing

Flashing on a Paradise roof gets punished. Sun bakes it, monsoon rain hits it in short violent bursts, and the temperature swings from a cool morning to a hundred-plus afternoon can open a seam that looked fine in March. Here’s what a failing piece looks like:

  • Rust streaks on the fascia or soffit below a wall joint. The metal has corroded through a bend or the sealant behind the counter-flashing has failed. Both mean water is running behind the metal instead of over it.
  • Curled or cracked sealant at the flashing edge. Sealant has a lifespan of about five to eight years in Paradise heat. Once it dries and pulls back, the joint is open and every storm finds it.
  • Staining on the underside of the roof deck near a wall. This is the one owners miss because you can’t see it from outside. It shows up as brown water marks on the decking inside the attic – a step flashing that’s lifted or short-nailed is the usual cause.
  • Visible separation between the flashing and the tile or shingle course. On tile roofs you’ll see daylight where the tile edge should sit tight to the flashing leg. On shingle roofs, a curled shingle edge over the flashing means the piece underneath is loose or undersized.
  • Water in the attic after a hard rain – but only near a wall or valley. If it’s only in one spot, it’s usually the flashing. If it’s everywhere, the roof itself is the problem. That’s the difference we check first.

If two or three of those line up, the flashing is the suspect, not the tile. Replacing the flashing is a small job. Replacing the deck because the flashing leaked for two seasons is not.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Here’s a real range for a Paradise Boral flashing replacement, installed with the sealant and fasteners included:

Scope Typical Installed Range
Single wall step flashing run, up to 10 linear feet $310 – $420
Wall flashing with counter-flashing tie-in, 10 – 25 linear feet $450 – $780
Valley flashing or vent stack flashing, Boral tile $520 – $1,100
Chimney or skylight flashing rework $780 – $1,450

What drives the range: the metal itself (galvanized versus painted steel versus copper), the tile or shingle profile and how much has to come up to reach the flashing, the pitch of the roof, and how much old sealant and old flashing has to be cut away before the new piece goes in. We quote parts and labor as separate line items so you can see exactly what the metal costs and what the work costs. Every flashing job we do is covered by our written 90-Day Done Right Promise – if it leaks after we’re done, one call brings us back, no argument. And if you’ve got a written estimate from another roofer, we’ll give you a free second opinion on it.

DIY or Call Us?

Some of this you can safely check yourself. Walk the roof from a ladder with your feet on the ground and look at the flashing edges with binoculars – rust, lifted metal, and cracked sealant are all visible. Go in the attic after a rain and look for water marks on the deck near a wall. That’s diagnosis, and it’s worth doing.

Replacing it is different. You’re working on a wet, pitched roof, prying up tile or shingle courses without breaking them, and cutting new flashing to fit a profile that has to tie into the wall behind it. On a two-story roof or a steep pitch, this is the kind of work where a slip means a fall, and where cutting a Boral tile course wrong means you’re buying new tile you didn’t plan on. We don’t recommend tearing into it yourself. Let us look, quote it in writing, and get the right piece in. Call (833) 676-0557 – a live person answers, not a call center.

FAQs

Need Roofing help nationwide? Licensed & insured · free written estimates
Call (833) 676-0557
Local Service Coverage

Request a Free Estimate in Paradise

Tell us what you need - Shepherd & Sons Roofing Paradise responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch