A Shepherd company - serving Paradise, NV

Boral Ridge Vent Installation in Paradise, NV

Architectural shinglesArchitectural shingles
Metal roofingMetal roofing
Tile roofingTile roofing
GAFGAF
Owens CorningOwens Corning
Flat & low-slopeFlat & low-slope
Every visit starts with

Free roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation

We have financing partners for your new roof*On approved credit; ask us about your options
Get your free estimate

Boral Ridge Vent Installation: The Paradise Owner’s Guide

Installing Boral ridge vent on a Paradise roof typically runs $420 to $780 installed for a standard single-story ranch, and a two-story or steeper-pitch home usually lands between $650 and $1,100 depending on linear feet and how much of the old vent and cap shingles have to come off first. That figure covers the vent material, the ridge cap, the nails, the labor, and hauling away the old pieces. We schedule these as planned work, usually within a week or two, and you’ll get an exact written number before anyone touches the roof.

Call (833) 676-0557

Owners in Paradise usually find out their ridge vent has failed the same way. There’s a brown water stain spreading across a bedroom ceiling after a hard monsoon, or the attic hits 140 degrees by early afternoon when it used to peak around 120. Sometimes it’s simpler: they climb up for the Christmas decorations and notice the ridge line looks wavy, or a neighbor points out cap shingles flapping in a gust. Whatever brought you here, a Boral ridge vent that’s quitting doesn’t fix itself, and the leak it lets in goes straight down into the decking.

Which Boral Models This Applies To

Boral makes this easy and hard at the same time. Their ridge vent is built to shed water and vent the same no matter which Boral roof tile or shingle line it’s sitting on, so the vent itself is the compatibility question – not the field product underneath. What matters is the profile: Boral’s low-profile vent is designed to sit under a standard ridge cap, while their high-profile version handles thicker tile ridges and steeper roofs. Get the profile wrong and it either won’t vent right or it’ll telegraph through the cap and look like a lump on your roofline. Same address since 1996, and we’ve set enough Boral to know which profile belongs where.

To identify yours, get up close (safely, from a ladder with someone spotting) and look at the vent strip under the ridge cap. Boral stamps the profile on their vent sections, and the old packaging or a contractor invoice will name the series. If neither turns up, measure the exposed vent slot and the ridge thickness and we’ll match it from there. On the OEM-or-aftermarket call: Boral’s own vent integrates cleanly with their cap system, but a quality equivalent in the same profile vents just as well and often costs less. We’ll tell you straight which one makes sense for your roof rather than upselling you into brand loyalty you don’t need.

Explore

Styles & brands we work with

  • Architectural shingles
  • Metal roofing
  • Tile roofing
  • GAF
  • Owens Corning
  • Flat & low-slope

Signs Your Boral Ridge Vent Installation Is Failing

  • Brown water stains running down a ceiling or wall. The vent’s cap shingles have lifted or the vent joint has opened, and water is tracking along the ridge and finding its way into the attic and out through the drywall below.
  • Attic temperatures climbing 15 to 25 degrees above where they used to be. The vent slot has clogged with dust, blown-in insulation, or critter debris, and hot air is trapped with nowhere to go but down into the living space.
  • Wavy or curled ridge cap shingles. Heat, sun, and a poorly seated vent underneath are all pushing on the cap, and once the shingles dance, the vent below isn’t sealed tight.
  • Daylight, dust, or moisture visible from inside the attic along the ridge. The vent has separated from the deck or a section has worked loose, which is a straight path for monsoon rain and the wind that comes with it.
  • Ridge cap shingles missing or flapping after a wind event. Fastener pattern or sealant failed, and once the cap is loose the vent itself is the next thing to go.

Paradise is hard on these parts. Our UV index sits high most of the year, monsoon winds gust hard across the valley in July and August, and the wide temperature swings between a 100-degree afternoon and a 60-degree night work the sealant and fasteners loose over time. A vent that lasted 20 years on the coast might give you 12 to 15 here, and if it wasn’t set right to begin with, you’ll see signs closer to 8. Our technicians have up to 30 years of experience reading exactly these failure patterns.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Plan on $420 to $780 installed for most Paradise homes, with steeper or larger roofs pushing toward $1,100. The spread comes down to four things: how many linear feet of ridge you have, the roof pitch (steeper means more setup and more safety gear), whether the old vent and cap come off cleanly or are rusted and glued down, and the vent profile you need. That’s the whole quote, parts and labor together.

Line item Typical Paradise range
Boral ridge vent material (or quality equivalent) $95 – $260 by linear feet and profile
Ridge cap shingles to match your roof $60 – $180
Fasteners, sealant, underlayment touch-up $25 – $50
Labor: removal, installation, cleanup $240 – $480
Installed total $420 – $1,100

No change orders once we start. No trip charge inside our county. Every job carries our written 90-Day Done Right Promise – if it’s not right, you make one call and Bill comes back and makes it right. And we’ll always show you the deck and the old vent before we talk money.

DIY or Call Us?

Some of this you can safely check yourself. From the ground with binoculars or a camera zoom, look for lifted cap shingles, missing pieces, and waviness along the ridge. Walk the attic on a cool morning and look for daylight, water stains, or a clogged vent slot. Note what you find.

Where DIY goes wrong is the roof itself. Ridge vent is right up at the peak, and Paradise roofs are often a 6/12 pitch or steeper. A fall from there is not a scraped knee. Beyond the height, cutting a proper vent slot through decking, seating the vent flush, laying the cap with the right nail pattern, and sealing the joints so monsoon rain doesn’t find the gaps is work that takes experience to get right the first time. We recommend a trained roofer here.

If you’re not sure what you’re looking at, call (833) 676-0557. A live person answers 24/7, not a call center, and Bill will give you a straight read.

FAQs

Need Roofing help nationwide? Licensed & insured · free written estimates
Call (833) 676-0557
Local Service Coverage

Request a Free Estimate in Paradise

Tell us what you need - Shepherd & Sons Roofing Paradise responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch