A Shepherd company - serving Paradise, NV

Boral Shingle Repair in Paradise, NV

Architectural shinglesArchitectural shingles
Metal roofingMetal roofing
Tile roofingTile roofing
GAFGAF
Owens CorningOwens Corning
Flat & low-slopeFlat & low-slope
Every visit starts with

Free roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation

We have financing partners for your new roof*On approved credit; ask us about your options
Get your free estimate

Boral Shingle Repair: The Paradise Owner’s Guide

Boral shingle repair in Paradise typically runs $450 to $1,400 installed for a partial repair involving genuine Boral-matched shingles, underlayment, and flashing, and we can usually get out to look at it within a day or two of your call. Full re-shingling of a single slope runs higher, from $1,900 to $4,200. Most Paradise owners don’t notice a problem until they’re up on a ladder after a wind event and see curls, missing tabs, or a little pile of mineral grit in the gutter. By then the shingle has been drying out in our high-desert sun for a while, and the repair is more than a spot patch. We’re an independent roofing company and not affiliated with Boral, but we’ve set Boral shingles on plenty of Paradise roofs and know what to look for.

Call (833) 676-0557

Which Boral Models This Applies To

Boral makes several shingle lines that show up on Paradise homes, and matching matters more than people think. The most common ones you’ll run into around here are Boral’s SteelShake (a stamped-steel shingle engineered to look like cedar shake), Boral’s composite slate and shake products, and the concrete and clay tile lines Boral is known for. Each has different nailing zones and overlapping dimensions, so a patch from the wrong line won’t sit flush no matter how carefully it’s cut.

To identify yours, look for the stamped or printed product name on the back of a loose tab, or check the underside of any shingle that’s already come free. If the label is gone, measure the exposure – the visible height of each course – and the tab width. SteelShake panels have a fixed panel dimension that tells you immediately if it’s the steel line. For the OEM-versus-aftermarket question: with Boral’s metal and composite lines, we recommend genuine Boral replacement pieces whenever the line is still in production, because the profile and finish coat are proprietary and an aftermarket look-alike will always read slightly off in color and shadow. When a line has been discontinued, we’ll be honest about it and talk through the closest match or a re-shingle of the affected slope.

Explore

Styles & brands we work with

  • Architectural shingles
  • Metal roofing
  • Tile roofing
  • GAF
  • Owens Corning
  • Flat & low-slope

Signs Your Boral Shingle Repair Is Failing

Here’s what Paradise owners usually spot first, and what’s actually going on underneath:

  • Curling or clawing at the tab edges. The sun bakes the top surface while the underside stays cooler, and over time that uneven stress pulls the edges up. Once they curl, wind gets under them and the seal is gone.
  • Granule loss in the gutters and at the downspouts. A little grit is normal in the first year. A steady buildup after several seasons means the protective coating is wearing through and the shingle is thinning.
  • Missing or lifted panels after a wind event. Boral’s steel and composite panels rely on a specific nailing pattern to hold their wind rating. When a panel lifts, it’s often because a nail was placed high or a seal strip failed, not because the panel itself was bad.
  • Cracked or split shingles around flashings and valleys. These are the spots where water concentrates and where the shingle flexes most. Cracks here usually mean the flashing seal has also failed.
  • Daylight or dark staining in the attic after rain. That’s the sign the shingle repair has already let water past the underlayment. This one needs attention sooner rather than later.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

In Paradise, an installed partial Boral shingle repair (matching shingles, new underlayment under the patch, flashing reset where needed) commonly lands between $450 and $1,400. A full re-shingle of a single slope runs $1,900 to $4,200. What drives the number is how much of the deck is exposed once we pull the damaged shingles, whether the flashing needs to be replaced rather than reset, and whether your Boral line is still in production or we’re matching a discontinued one.

We quote parts and labor separately so you can see exactly what you’re paying for. Every roofing job we do is covered by our written 90-Day Done Right Promise – if it’s not done right, one call brings Bill back. We’ll show you the deck photos before we talk money.

DIY or Call Us?

An owner can safely check a few things from the ground: look for grit in the gutters, scan the roof with binoculars for lifted or missing panels, and check the attic after rain for staining. Where DIY goes wrong on Boral shingles is getting on the roof itself. Steel and composite panels are slick, the nailing pattern has to be precise to hold the wind rating, and a bad patch around a flashing can leak for a year before you notice. Roof work at height is genuinely dangerous, and we’d rather you stay off it. If something’s off, call (833) 676-0557 and we’ll come take a look.

FAQs

Need Roofing help nationwide? Licensed & insured · free written estimates
Call (833) 676-0557
Local Service Coverage

Request a Free Estimate in Paradise

Tell us what you need - Shepherd & Sons Roofing Paradise responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch