Metal roofing
Architectural shingles
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Boral Specialty Roofing in Paradise: What to Know First
Boral specialty roofing in Paradise usually means low-slope and flat work: TPO, EPDM, modified bitumen, built-up, green roofs, and solar-ready assemblies. Most repairs take one to three days once we’ve seen the deck; full replacement on a typical Paradise flat section runs one to three weeks depending on size and weather. We give you a written line-item price before anyone touches your roof, and the number doesn’t change mid-job.
This page is for the homeowner who already has a Boral membrane or panel up there and wants someone who won’t learn on it. We’re an independent Boral service provider, not affiliated with or authorized by Boral, and we’ll say so plainly. If you want the straight answer on what’s wrong and what it costs, call (833) 676-0557.
How Boral Products Fail – and How We Fix Them
Boral makes good membranes. Failure usually comes from installation detail or Paradise’s sun and wind load, not the roll itself. Here’s what we actually see and what we do about it:
- Heat-welded seam peeling on Boral TPO. Paradise summers cook these roofs, and a seam welded too cool or too fast lets go along the lap edge, not in the field. You’ll see the membrane lift and curl at a seam before you see a leak inside. We cut back the failed lap, clean it, re-weld at the right temperature, and probe-test the seam before we leave.
- Ponding water at Boral EPDM field splices. EPDM is forgiving, but a splice tape that sat too long before rolling, or a low spot the original installer ignored, traps water and breaks the adhesive down. We find the actual low point with a water test rather than guessing, then correct the drainage or rebuild the splice with primer and proper lap pressure.
- Granule loss and alligatoring on Boral modified bitumen cap sheets. UV eats the surfacing on a south-facing Paradise cap sheet faster than the rest of the roof, and once granules are gone the asphalt dries and cracks. We check how deep the aging goes; if the base sheet is still sound, a resurfaced cap can buy years. If not, we say so.
- Flashing failures around Boral built-up and solar-ready assemblies. The membrane outlasts the details. Pipe boots, edge metal, and penetration wraps fail first, and on a solar-ready roof the mounting points are where water gets in. We rebuild the flashings to spec rather than smearing sealant over a crack that will reopen.
- Tears and punctures at transitions on Boral green-roof systems. Root barriers and planting media hide damage until it’s wet underneath. We check the waterproofing layer and drainage mat where foot traffic and overgrowth concentrate, then patch with compatible Boral material so the warranty stays intact.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Our Boral Specialty Roofing Process
Same approach whether it’s a small Boral EPDM patch or a full TPO re-cover in Paradise. We show you the deck photos before we talk money.
- 1
The call. A live person answers, day or night. We ask what you’ve got up there and set a time to look.
- 2
On the roof. We photograph the seams, flashings, and deck, and measure squares. A roof is measured in squares – ask any bidder how many they counted.
- 3
The parts decision. We use Boral-compatible material wherever the warranty requires it. Where a quality aftermarket flashing or fastener is the stronger choice, we tell you why, and we don’t swap in cheap parts to shave the bid.
- 4
The repair. Background-checked crew, and Bill’s own sons are on the roof with him. We weld, splice, and flash to the manufacturer’s detail requirements.
- 5
The test. Water test on flat sections, seam probe on welded work. We don’t call it done until it holds.
- 6
The cleanup and the promise. We walk the property, haul off debris, and hand you the written 90-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterWhat Boral Specialty Roofing Costs in Paradise
These are honest ranges for the work we do most in Paradise. Your written estimate is the real number, and a free second opinion on any bidder’s quote is always available.
| Job | Typical range |
|---|---|
| Single seam re-weld or small TPO repair | $275 – $650 |
| EPDM splice rebuild or flashing repair | $350 – $900 |
| Modified bitumen cap sheet resurface (small section) | $900 – $2,400 |
| TPO or EPDM re-cover, flat section | $5,500 – $14,000 |
| Full Boral flat-roof replacement | $12,000 – $32,000 |
What moves the price: roof size and access, how much deck repair is hiding under the membrane, penetration count, number of flashings, and material choice. We keep it simple – no trip charge inside our own county, and $40 off any repair over $200. Call (833) 676-0557 to schedule your free estimate.
Why Paradise Homeowners Call Shepherd & Sons Roofing Paradise for Boral Work
Same address since 1996, same name on the truck, same owner on the roof. Ask the storm chasers who roll through Paradise after every storm where theirs is. I publish my address and license number, my name is on the work, and I answer my own phone – nights and weekends included.
Every roofing job carries the written 90-Day Done Right Promise. If it’s not right, one call brings Bill back. Our technicians have up to 30 years of experience, and we set Boral alongside GAF, Owens Corning, and CertainTeed, so we’re not pushing one brand – we’re solving your roof. Seniors and veterans get 10% off. Call (833) 676-0557 for a free estimate, and we’ll show you what’s really up there.
FAQs
Does repairing my Boral roof void the warranty? Not if it’s done with Boral-compatible materials and proper detail work. We use spec material wherever the warranty requires it, document what we did, and tell you plainly if a repair would put coverage at risk. Call (833) 676-0557 for a free estimate.
Can you get Boral parts in Paradise? Yes – Boral membrane, cap sheet, and flashing material are available through regional suppliers, though some specialty items take a few days to order. We tell you upfront what’s in stock and what isn’t before we start.
Should I repair or replace my flat Boral roof? Repair if the membrane field is sound and the failure is at seams or flashings; replace if water has reached the deck over a large area or the cap sheet is fully aged. We check the deck, not just the surface, before recommending either way.
How fast can you get out to look at a Boral roof in Paradise? A live person answers the phone 24/7, and we schedule assessments quickly for storm-damaged flat roofs. For a planned replacement, we’ll set a realistic date rather than promise same-day work nobody can deliver.
Will the price change once work starts? No. You get a written line-item estimate before we begin, and if we find hidden deck damage, we stop, show you the photos, and get your approval before the number moves. Call (833) 676-0557 – estimates are free.
Written by the team at Shepherd & Sons Roofing Paradise, serving Paradise and nearby areas.