Metal roofing
Architectural shingles
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Boral Metal Roofing in Paradise: What to Know First
We handle Boral metal roofing in Paradise as an independent Boral service provider, and most repairs and replacements run two to four weeks from the first call to a finished, walkable roof. Boral is a manufacturer – they make the panels and tile profiles, not the labor – so what you’re really paying for is the install and the follow-through on your Paradise property, and we quote that in writing before anyone touches your roof.
If you own Boral metal, whether it’s the steel shingle look or a standing seam panel, this page is for you. It’s written for the homeowner who’s had a leak, a fading finish, or a bid that felt like a guess. Call (833) 676-0557 and a live person answers, day or night.
How Boral Products Fail – and How We Fix Them
Boral makes good metal. The failures we see on Paradise roofs almost always come from the install or the environment, not the panel itself. Here’s what we actually run into.
- Standing-seam panels walking loose at the clips. Boral standing seam moves as it heats and cools, and if the original crew over-tightened the clips or skipped the sliding clip detail, you get a roof that rattles and backs screws out. We reset the clips to the right tension and check every seam, because a tight clip is what earns the wind rating, not the panel label.
- Granular finishes chalking on Boral steel shingles. Paradise gets brutal afternoon sun and near-zero humidity, and a Boral steel shingle catching full west sun will show chalk and fade years before one under shade. We tell homeowners this upfront and quote a coating or a full panel replacement, depending on how far the finish has gone.
- Valley and penetration leaks on corrugated Boral profiles. Corrugated panels are only as good as the flashing at the valleys, chimneys, and vent boots. In Paradise we regularly see these leaks where the original crew re-used old flashing instead of replacing it, and water tracks back under the panel instead of off it. We cut out and rebuild those junctions with new metal.
- Fastener corrosion and backed-out screws. Boral panels held by exposed screws will weep at the washers after enough heat cycles, and on a Paradise roof with a lot of sun exposure the neoprene washers dry out first. We pull the bad fasteners, replace the washers with the right grade, and check the whole field, not just the one spot that’s dripping.
- Rusted cut edges on aluminum and steel panels. Cheap field cuts leave bare metal that rusts from the edge in, and it’s one of the most common things a homeowner can’t see from the ground. We re-cut or seal those edges with a proper edge treatment so the panel doesn’t fail from the inside out.
One thing Boral’s own site won’t tell you: a Boral steel shingle that’s losing its finish on the south slope of a Paradise roof often looks fine on the shaded north side, so a homeowner gets told “the roof’s fine” when half of it isn’t. We walk all four sides and show you the deck photos before we talk money.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Our Boral Metal Roofing Process
- 1
We come out and look. Bill and his crew get on the roof, measure it in squares, and find the actual leak path – not the stain on the ceiling. No trip charge inside our own county.
- 2
We show you the deck photos. Before any number, you see what we see. Then we talk money.
- 3
We make the parts call. OEM Boral parts are the safe bet for finish match and warranty, but a quality aftermarket flashing or fastener can do the job for less where the finish doesn’t matter. We’ll tell you which one your job actually needs, plainly.
- 4
We do the repair or replacement. Clips, panels, flashing, fasteners – done to Boral’s install spec so the panel keeps its warranty and the wind rating holds.
- 5
We test it. Water test, seam check, and a walk of every penetration before we call it done.
- 6
You get the 90-Day Done Right Promise in writing. If it’s not done right, we make it right. One call brings Bill back.
What Boral Metal Roofing Costs in Paradise
Every job is different, but here’s the honest ballpark for Boral metal work in Paradise:
| Job | Typical Range |
|---|---|
| Boral metal roof repair (leaks, flashing, fasteners) | $450 – $1,800 |
| Boral metal roof coating / re-finish | $2,500 – $6,500 |
| Boral standing seam or steel shingle replacement (full roof) | $10,000 – $28,000+ |
What moves the price: roof size in squares, how many valleys and penetrations, whether we’re matching a Boral finish or doing a quality aftermarket part, and the pitch of the roof. We give free written estimates with line items, so you know the number before anyone touches your roof. Call (833) 676-0557 for yours.
See the difference
Before
After
Before
After
Before
AfterWhy Paradise Homeowners Call Shepherd & Sons Roofing Paradise for Boral Work
We’ve been at the same address since 1996, locally owned and owner-operated, with a published license number and Bill’s name on the work. Storm chasers roll through Paradise after every hail event and disappear; ask them where their shop is. Our technicians have up to 30 years of experience, and Bill’s own sons are on the roof with him – background-checked, in uniform, same crew you’ll see at the hardware store on Saturday.
We install Boral metal, and we also work with GAF, Owens Corning, and CertainTeetle if Boral isn’t the right fit for your roof. Every roofing job comes with the written 90-Day Done Right Promise. A live person answers the phone 24/7, including nights and weekends after a storm. You get a Free Second Opinion on any written estimate and a Senior and Veteran 10% discount, always.
FAQs
Does repairing my Boral metal roof void the warranty? Not if it’s done to Boral’s install spec with the right parts. Improper flashing or fastener work can void it, which is why we use OEM or spec-matched parts and document what we did. Call (833) 676-0557 for a free estimate.
Can you match my Boral panel finish? Usually yes, with OEM panels for an exact match, or a close aftermarket finish if the original is discontinued. We’ll tell you which options actually exist for your panel before you commit.
Should I repair or replace my Boral metal roof? Repair if the issue is a few fasteners, flashing, or a localized leak. Replace if the finish has failed across a whole slope or the panels are corroded through the edge. We walk the whole roof and tell you which one you’re looking at.
How fast can you get to a Boral metal leak in Paradise? We answer the phone 24/7 and will get out to look as soon as we can – no call center, no form. Call (833) 676-0557 and a real person picks up.
Do you pull permits for Boral metal work in Paradise? Yes – we pull the permits and see the inspections through, so the job is on record and done right.
Get Your Boral Metal Roof Sorted
If you’ve got a Boral metal roof in Paradise that’s leaking, fading, or just due for a hard look, call (833) 676-0557 for a free estimate. We’ll show you the deck photos, give you a straight number, and stand behind it with the 90-Day Done Right Promise. Same address since 1996 – ask the storm chasers where theirs is.
Written by the team at Shepherd & Sons Roofing Paradise, serving Paradise and nearby areas.