Metal roofing
Architectural shingles
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Tamko Specialty Roofing in Paradise: What to Know First
We provide independent Tamko specialty roofing in Paradise, and most jobs run one to three days from tear-off to final inspection depending on which system you’re running and how much decking has to be replaced. Tamko’s low-slope and solar-ready lines hold up well here, but they fail in specific ways, and we price the fix honestly before anyone touches your roof. We’re not the cheapest bid you’ll get in Paradise, and we don’t pretend to be. We’re the crew that shows you the deck photos before we talk money.
This page is for Paradise homeowners who own a Tamko roof – a solar-ready shingle assembly, a TPO membrane, an EPDM rubber roof, a modified bitumen cap sheet, a green roof system, or a built-up roof – and need specialty work done right the first time. As an independent Tamko service provider, Shepherd & Sons Roofing Paradise is not affiliated with or authorized by Tamko, so our advice is our own. Call (833) 676-0557 and a live person picks up.
How Tamko Products Fail – and How We Fix Them
Every brand has its weak spots, and Tamko is no different. We’ve pulled enough Tamko roofs off Paradise homes to know which failures come back season after season. Here’s what we actually see.
- Tamko Solar Ready shingles going bald at the south-facing ridge. The granular surface on Solar Ready shingles wears faster where the sun hits hardest, and in Paradise that’s the south and west planes. When the granules wash into the gutter, the mat underneath starts drying out. We don’t reshingle the whole roof to fix a ridge – we match the series, replace the worn courses, and check the underlayment while the shingles are up.
- TPO membrane seams that pull apart at the wall termination. Tamko TPO is a good membrane, but the seam at a parapet wall takes the thermal cycling hard here – warm days, cold desert nights, repeat. When the termination bar loosens, water gets behind the flashing. We re-terminate the seam, add a proper cover strip, and pressure-test the edge before we close it up.
- EPDM rubber shrinking at the perimeter. Tamko EPDM is reliable, but rubber contracts over time, and at the perimeter it pulls back from the edge and opens a gap. That’s where water finds its way in. We re-stretch and re-flash the perimeter, and we check the fasteners at the same time because a shrink usually means the original install was stretched too tight.
- Modified bitumen blistering where the cap sheet meets the base. Tamko modified bitumen handles heat, but if the base sheet wasn’t fully adhered during the original install, trapped moisture blisters the cap sheet after a few summers. We cut out the blister, dry the deck, and re-lay the cap so the layers bond the way they’re supposed to.
- Built-up roofing ponding at the low points. Tamko built-up systems (and the coatings that go with them) pond where the deck has settled. Ponding isn’t a roofing problem on its own – it’s a drainage problem the roof is telling you about. We re-slope the low spots and add drains rather than just coating over the water.
None of these are Tamko’s fault. They’re the interaction between the product, this climate, and how the original crew set it. That’s the part we know how to read.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Our Tamko Specialty Roofing Process
Every Tamko job we do in Paradise follows the same path from your call to the sweep-up. No surprises, no moving numbers.
- 1
You call and a live person answers. Not a form, not voicemail. We ask what you’ve got – the series if you know it, the age of the roof, and what you’re seeing – and we set a time to come out.
- 2
We walk the roof and photograph the deck. We get up there, take pictures, and show you what we see before we talk money. That’s not a sales tactic. It’s how you know the bid is real.
- 3
We measure in squares and give you a written line-item estimate. Ask any bidder how many squares they counted. If they can’t tell you, they didn’t measure. We do, and the number we write down doesn’t move once work starts.
- 4
We make the parts decision out loud. On Tamko systems, we use OEM components where the warranty depends on it – terminations, fasteners, and cap sheets matched to the series. Where a quality aftermarket part is just as good and saves you money, we say so, and you decide.
- 5
We do the work and test it. Seams get pressure-checked, drains get flow-tested, and we take photos of the finished assembly so you have a record.
- 6
We clean up and hand you the written 90-Day Done Right Promise. If something isn’t right, one call brings us back. That’s on paper on every roofing job, Tamko or otherwise.
See the difference
Before
After
Before
After
Before
AfterWhat Tamko Specialty Roofing Costs in Paradise
Here’s what common Tamko specialty work runs in Paradise. These are real ranges for our market, not teaser numbers, and the low end assumes a straightforward job with the deck intact.
- TPO membrane repair, single seam or termination: $450 to $900.
- EPDM perimeter re-flash and re-stretch: $600 to $1,200.
- Modified bitumen blister repair, spot: $500 to $1,100.
- Built-up roof re-slope and drain work: $900 to $2,400 depending on square footage and drain count.
- Solar Ready shingle repair, ridge or worn courses: $400 to $1,000.
- Full specialty system replacement (TPO, EPDM, mod-bit, built-up): $8,000 to $22,000 for most Paradise homes, priced by the square.
What moves the price: how many squares, how much decking is soft, whether the assembly needs a full tear-off or can be recovered, and whether the parts are OEM or aftermarket. We don’t add trip charges inside our own county, and your first look at the roof is free. Call (833) 676-0557 to schedule your free estimate – the number we quote is the number you pay.
Why Paradise Homeowners Call Shepherd & Sons Roofing Paradise for Tamko Work
We’ve been at the same address since 1996, and that’s the whole pitch. Out-of-state storm chasers roll through Paradise after every hailstorm, quote one price on the phone, and want a different number at the door. We’re the opposite. Same shop, same name on the truck, same owner on the roof, every job.
Our technicians have up to 30 years of experience, and they’ve set enough Tamko to know the difference between a series problem and an install problem. We also install GAF, Owens Corning, CertainTeed, IKO, Atlas, and Boral, so if Tamko isn’t the right fit for your roof, we’ll tell you honestly. Every roofing job comes with the written 90-Day Done Right Promise. A live person answers the phone around the clock, including after a storm. And we offer a free second opinion on any written estimate, so you can compare before you commit.
FAQs
Not if the repair is done right. Tamko’s warranty depends on the assembly staying matched to the series – the right terminations, fasteners, and cap sheets – so we use OEM components where the warranty requires it and document what we used. As an independent Tamko service provider, we’re not Tamko, but we know what their warranty terms expect and we keep your paperwork clean. Call (833) 676-0557 if you want us to read your warranty with you.
Most standard Tamko components – TPO membrane, EPDM, modified bitumen cap sheets – are available without a long lead time, though specialty or discontinued series can take longer. We tell you honestly on the estimate how long your specific product will take to source. Call (833) 676-0557 and tell us the series.
Repair if the deck is sound, the failure is localized, and the assembly is under roughly 15 years old. Replace when the failure is widespread, the deck is soft in multiple spots, or the series has been discontinued. We show you the photos and give you both numbers, and you decide – no pressure. Call (833) 676-0557 for a free estimate on either path.
We schedule specialty work within a few days for standard repairs, and full replacements get on the calendar as soon as you approve the estimate. Storm damage after a hailstorm can push the schedule, but a live person answers the phone even after hours. Call (833) 676-0557 and we’ll tell you the real timeline.
No. We measure in squares, write a line-item estimate, and the number doesn’t move unless you approve a change in writing. If we find soft decking after tear-off, we show you the photos and give you the additional number before we do anything. Call (833) 676-0557 for a written estimate that holds.
Your Tamko roof deserves a crew that knows the product and answers the phone. Call Shepherd & Sons Roofing Paradise at (833) 676-0557 to schedule your free estimate, get a second opinion on any written bid, or just talk through what you’re seeing up there. Same address since 1996, and the name on the truck is the name on the license.
Written by the team at Shepherd & Sons Roofing Paradise, serving Paradise and nearby areas.