Metal roofing
Architectural shingles
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Tamko Metal Roofing in Paradise: What to Know First
We provide independent Tamko metal roofing in Paradise, and most residential metal roof projects here run anywhere from a one-day repair to a two-to-four day installation depending on the panel count and pitch. On price, we’re honest up front: small metal repairs usually land in the low hundreds, while a full standing seam replacement on a typical Paradise house runs into the five figures, and we’ll show you the deck photos before we ever talk money. This page is for Paradise homeowners who already have a Tamko roof, or a Tamko product on their home, and want metal work done by someone who knows what they’re looking at. Call (833) 676-0557 and a live person picks up, day or night.
Key Takeaways
- We’re an independent Tamko service provider, not affiliated with or authorized by Tamko. We just know their products cold.
- Metal repairs typically run $350 – $900; full standing seam replacement in Paradise often falls between $18,000 and $42,000 depending on square count and panel type.
- Every roofing job carries our written 90-Day Done Right Promise, and one call brings Bill back if something’s off.
- Free Second Opinion on any written estimate, no trip charge inside our own county.
How Tamko Products Fail – and How We Fix Them
Tamko makes a range of metal products, from their MetalWorks shingle-style panels to their standing seam and corrugated lines, and each one tends to show its age in a specific way. Here’s what we actually see on Paradise roofs and how we handle it.
- Sealant failure at panel laps on MetalWorks shingle panels. The butyl sealant tape under the overlapping panels dries out and lets wind-driven rain creep under. It’s not a panel problem, it’s an age problem, and it happens faster in Paradise’s summer heat where attic temps push past 140°F. We lift the affected laps, clean the old sealant off, and reset them with fresh sealant and the correct fastener pattern, not just a caulk-and-run fix.
- Fastener back-out on corrugated steel. Tamko’s corrugated panels expand and contract with the desert temperature swings, and over time the fasteners work loose at the purlins. We replace the backed-out screws with the right length and a proper washer, and we check the gaskets on the surrounding fasteners so you don’t trade one leak for another.
- Rust bleeding at cut edges and penetrations. Any panel cut on site leaves an exposed edge, and on steel products that edge rusts first. In Paradise we see this at vent boots and ridge caps where the original install didn’t touch up the cut. We treat the rust, prime it, and re-seal correctly.
- Granule and coating wear on metal shingle panels. The stone-coated finish on shingle-style metal panels breaks down on south-facing slopes first. It’s cosmetic until the substrate starts showing, but once you see bare metal, moisture is getting in. We evaluate whether a coating refresh buys you years or whether it’s replacement time.
- Improperly flashed valleys and sidewalls. This isn’t a Tamko defect, it’s an install defect, but it’s the number one reason a metal roof leaks early. We re-flash the transitions properly with the right metal, not just sealant.
That last one is worth saying plainly: most of the metal roof calls we get in Paradise aren’t the panel’s fault. They’re the flashing and fastener work underneath. When the guys on the roof open it up, we find out which it is.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Our Tamko Metal Roofing Process
Here’s how a Tamko job runs from your first call to the last nail swept up.
- 1
You call, a real person answers. Not voicemail, not a form. We’ll set a time for Bill to come out.
- 2
We look at the roof, not just the leak. Bill and his crew get up there, check the panels, the fasteners, the flashing, and the deck underneath where it matters. We take photos so you can see what we see.
- 3
We decide on parts. Sometimes Tamko OEM fasteners and sealant are the right call to keep your warranty intact. Sometimes a quality aftermarket fastener does the same job for less. We’ll tell you which and why, in plain language.
- 4
We do the work. Repairs get done right the first time with the correct materials for metal, not roofing cement. Replacements get a written line-item quote first so you know the number before anyone touches your roof.
- 5
We test it. Water test at the repair, visual check at every fastener and seam. If it’s not right, we’re not done.
- 6
We clean up and back it in writing. Every job carries our 90-Day Done Right Promise. If something’s off, one call brings Bill back.
See the difference
Before
After
Before
After
Before
AfterWhat Tamko Metal Roofing Costs in Paradise
Metal work on a Tamko roof in Paradise isn’t one price, because a re-seal on a few panel laps and a full standing seam replacement aren’t the same job. Here are the ranges we see most often.
| Job Type | Typical Range in Paradise |
|---|---|
| Sealant and fastener repair (small area) | $350 – $900 |
| Flashing re-do at valleys or sidewalls | $500 – $1,400 |
| Metal roof coating refresh | $2,500 – $6,500 |
| Standing seam metal roof replacement | $18,000 – $42,000 |
| Corrugated or metal shingle panel replacement | $12,000 – $28,000 |
What moves the price: the number of squares on your roof, the pitch, whether the old panels have to be torn off or can be gone over, and whether your flashing is in good shape or needs to be rebuilt. A simple repair stays simple. A replacement on two stories with a lot of valley work costs more.
Call (833) 676-0557 for a free estimate. We’ll give you an honest number and a Free Second Opinion on any written estimate you already have. No trip charge inside our own county.
Why Paradise Homeowners Call Shepherd & Sons Roofing Paradise for Tamko Work
We’ve been at the same address since 1996, and we install products from Tamko, GAF, Owens Corning, and CertainTeed, so we’re not pushing one brand at you. If Tamko is the right fit, that’s what we’ll tell you. If it’s not, we’ll say so. The crew that shows up is Bill’s own, background-checked and uniformed, and his sons are on the roof with him. Our technicians have up to 30 years of experience with metal products like these, and they’ll tell you the difference between a panel problem and a flashing problem before you spend a dime.
You can look up our license, our address, and our name. We answer the phone 24/7 with a live person, including nights and weekends after a storm. Every roofing job is backed by our written 90-Day Done Right Promise, and we offer $40 Off Any Repair Over $200 plus a 10% discount for seniors and veterans. We’re not the cheapest bid in Paradise, and we’ll tell you that too. We’re the one your neighbor used and still says hello to on Saturday.
FAQs
Not if the repair uses compatible materials and correct fastening, which is exactly what we do. We’re an independent Tamko service provider, not a Tamko dealer, so we don’t speak for the manufacturer’s warranty, but we follow practices that keep it intact and we’ll tell you up front if a proposed fix would jeopardize it.
Yes. Tamko OEM fasteners, sealant tape, and matching panels are available on order, and we’ll often use a quality aftermarket fastener where it does the same job for less. We’ll tell you which we’re using and why before we start. Call (833) 676-0557 to schedule your free estimate.
We answer the phone 24/7 with a live person, not a call center or voicemail, so you’ll know when Bill is coming. For active leaks we work to get out as soon as we can, and repairs get scoped at the free estimate.
If the panels are sound and the problem is flashing or fasteners, repair usually makes sense and saves you money. If panel laps are failing across the whole roof or the coating has gone, replacement is the better spend. We’ll show you the photos and give you an honest read, not a sales pitch.
No. The Free Second Opinion on any written estimate is a standing offer, and there’s no trip charge inside our own county. Call (833) 676-0557 and we’ll get you a straight answer.
Written by the team at Shepherd & Sons Roofing Paradise, serving Paradise and nearby areas.