Architectural shingles
Metal roofing
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
IKO Gutters & Accessories in Paradise: What to Know First
We install, repair, and replace gutters and accessories on IKO-roofed homes throughout Paradise, and most jobs are finished in a single visit once the right parts are on hand. A standard repair runs $180 to $420, a full seamless gutter replacement on a typical Paradise ranch home lands between $1,400 and $3,200, and we give you a written line-item estimate before anyone touches your roof. As an independent IKO service provider, Shepherd & Sons Roofing Paradise works on IKO roofing systems every week, and we know where their edge metal, drip edge, and gutter interfaces tend to give first.
This page is for the homeowner who already has IKO shingles or IKO edge components on the roof and wants gutters that actually work with them, not a generic aluminum crew that treats every roof the same. Call (833) 676-0557 and a live person picks up, day or night.
How IKO Products Fail – and How We Fix Them
IKO makes solid roofing products, but their edge and gutter-related components have specific weak points that show up fast in Paradise’s climate. Here’s what we see and how we handle it.
- IKO drip edge that pulls away from the fascia. IKO’s aluminum drip edge is thin-gauge, and when the fascia behind it has any softness from monsoon-season splash-back, the nails lose bite and the edge lifts. Once it lifts, water runs behind the gutter instead of into it. We replace the fascia board first, then set new drip edge with proper nailing into solid wood, not just into whatever’s left of the old board.
- IKO gutter apron corrosion at the roof-to-gutter seam. On homes where the IKO apron sits tight against the fascia, wind-driven rain in a Paradise summer storm wicks into that seam and starts surface corrosion within a few seasons. We clean it back, prime the cut edge, and re-set the apron with a small standoff so water sheds instead of pooling.
- IKO edge metal that doesn’t line up with a new gutter run. This is the one that catches people. A gutter company installs new seamless gutters, and the existing IKO drip edge or apron sits a quarter-inch off the new hanger line, so the gutter never fully tucks under the edge. Water misses the gutter on the low side. We measure the IKO edge profile before we cut a single gutter section.
- IKO shingle overhang that’s too short or too long at the eave. IKO’s installation specs call for a specific overhang at the eave, and when it’s off, the first course of shingles either dumps water past the gutter or hangs so far it blocks the gutter opening. We check the overhang on the first three feet of eave and flag it before gutter work starts.
- Downspout strain from IKO-heavy roof assemblies. IKO shingle systems, especially with a full underlayment stack, add weight, and the fascia and soffit carry more load. Downspout brackets that were fine on the original build can loosen. We re-anchor downspouts into framing, not just fascia skin.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Our IKO Gutters & Accessories Process
- 1
You call, we listen. A live person answers (833) 676-0557 any hour. We ask what’s happening: overflow at a corner, a sagging run, water behind the gutter, or a full replacement. We book a time that works for you.
- 2
We come out and look at the roof, not just the gutter. Bill and his crew get on the roof, check the IKO edge metal, drip edge, apron, fascia, and shingle overhang at the eave, and take deck photos. You see the photos before we talk money.
- 3
Parts decision, explained. Where IKO OEM edge components are available and appropriate, we use them. Where a quality aftermarket drip edge or apron performs better in Paradise’s heat and monsoon cycles, we say so and show you why. Either way, you know what’s going on your house.
- 4
The repair or install. New fascia where it’s soft, new drip edge and apron set correctly, seamless gutters sized to the roof’s actual drainage load, downspouts anchored to framing, and gutter guards fitted to the profile. No shortcuts on hangers.
- 5
The water test. We run water at the high end of every run and watch it move. If it doesn’t flow clean to the downspout and away from the foundation, we’re not done.
- 6
Cleanup and the written promise. We haul off old material, sweep the ground, and hand you the written 90-Day Done Right Promise. If something’s not right, one call brings Bill back.
See the difference
Before
After
Before
After
Before
AfterWhat IKO Gutters & Accessories Costs in Paradise
Here’s what IKO-related gutter and accessory work runs in Paradise. These are real ranges from jobs we’ve done, and your written estimate will be itemized to the dollar.
- Gutter repair (reseal, re-hang, re-pitch one run): $180 – $420
- Drip edge and gutter apron replacement with fascia repair: $350 – $850
- Downspout repair or replacement (per run): $150 – $400
- Gutter guard installation (per linear foot): $6 – $14
- Seamless gutter replacement, typical Paradise home: $1,400 – $3,200
What moves the price: roof pitch and access, how much fascia is soft, whether the IKO edge profile needs correction, guard type, and how many stories we’re working at. Call (833) 676-0557 for an exact quote. Estimates are free, and there’s no trip charge inside our own county.
Why Paradise Homeowners Call Shepherd & Sons Roofing Paradise for IKO Work
We’ve been at the same address since 1996, and the name on the truck is the name on the license. Bill Shepherd’s crew is background-checked and uniformed, and Bill’s own sons are on the roof with him. Our technicians have up to 30 years of experience, and we’ve set enough IKO, GAF, Owens Corning, and CertainTeed to know which edge components hold up in Paradise and which ones don’t.
Every job comes with the written 90-Day Done Right Promise. We answer the phone 24/7 with a live person, not a call center. And when we quote a number, that’s the number. No surprise at the door. Ask anyone on your street. The storm chasers come and go after every hailstorm. We’re still here.
FAQs
No, gutter and edge-metal work doesn’t void your IKO shingle warranty as long as nothing disturbs the shingles themselves. We work around the shingle field and never nail through the shingle course. If an edge issue requires lifting shingles, we tell you before we start. Call (833) 676-0557 to schedule a free look.
Usually yes. We measure the IKO drip edge and apron profile on your roof and fit the new gutter run to it, so water sheds clean into the gutter instead of behind it. If OEM IKO edge components are available, we’ll use them; if a quality aftermarket piece performs better here, we’ll show you the comparison. Call for a free estimate.
Repair if the gutter itself is sound and the issue is hangers, sealant, pitch, or fascia. Replace if the runs are undersized for the roof, more than a quarter of the length is pitted or split, or if the IKO edge is sitting off the hanger line. We’ll tell you straight which side of that line you’re on. Estimates are free.
A live person answers the phone any hour at (833) 676-0557, and we set a visit time that fits your schedule. There’s no trip charge inside our own county, and you’ll see the deck photos and a written itemized estimate before any work starts.
Yes. We match the guard to the IKO edge profile and the gutter size, and we anchor it so wind doesn’t lift it during monsoon season. Guard installs run $6 – $14 per linear foot depending on the guard type and roof access. Call for a free estimate.
Written by the team at Shepherd & Sons Roofing Paradise, serving Paradise and nearby areas.